Exactly how to Replace a Bathtub ( Guide).
Exactly how to Replace a Bathtub ( Guide).
Blog Article
Right here down the page you can find a bunch of decent expertise related to Installing A Bathtub.
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately challenging project. If the old tub is conveniently obtainable, the job can move rapidly; if you have to open up a wall surface to get rid of the old bathtub and place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub and do not need to transform the arrangement of your previous water pipelines.
Your tools and product list ought to comprise the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted access that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the remaining water that will originate from the pipelines. When the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the producer offered backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The previous kind needs to be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using the two wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water supply and examine all joints and brand-new pipework for leaks and also tighten them if necessary. Load the bathtub as well as also check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and securing around the tub ought to wait until the bath tub has actually been utilized a minimum of when as this will certainly resolve it right into its final position.
Planning for the Installment
Firstly, the supporting structure supplied with the bath must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath and the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that article about Tools You Need to Install a New Bathtub while surfing around the web. Make sure you take the time to share this blog post if you liked it. Thanks a bunch for your time. Don't forget to come visit our website back soon.
Schedule Today Report this page